Vehicles
52 not categorized PORSCHE TORSION BARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.91134111502 Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car.
From $27.50
Make a selection 91434310700 View/Change Diagram
$109.25
Make a selection
$487.73
Make a selection
$1,052.22
Make a selection
$51.75
Make a selection 95133310430 Known as: torsion bar 25.5 mm View/Change Diagram
$266.49
Make a selection 94433311500 Known as: torsion bar 23.5 only together with stabiliser 14 / torsion bar 23.5 / torsion bar 23.5 mm View/Change Diagram
$1,052.22
Make a selection 95133310330 Known as: torsion bar 25.5 mm View/Change Diagram
$278.72
Make a selection P909218 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 968 1992-95
$341.99
Make a selection 91133300905 Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new OEM spec. (65 shore) rubber bushings clearly marked for accurate installation and indexing made in Germany sold individually. 2 necessary per car. Plea...(choose a part on the right to read more) View/Change Diagram
From $273.90
Make a selection 115900944018CS Sports suspension for 924 - 944 - 968 only for 18mm spring strut mounting this sports suspension is for everyday use and increase the dynamic and response. The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$3,132.80
Make a selection 90134147500 This is the grease seal for the torsion bar. always replace it when replacing the bar. Sold each. View/Change Diagram
From $6.85
Make a selection 86411039SPORT Koni front sport shock Porsche 911 Carrera 75-89 General Fitment911 1974-77
$256.61
Make a selection P910160 Adjustable spring plates are the ultimate way to lower or raise your vehicle all at the turn of a bolt. They allow you to weight balance the rear of the car so it performs the same in left-hand and right-hand corners. You avoid all the frustration and wasted time trying to guess at correct torsion bar spline placement, or having to redo one side to correct car height. Complete with plastic bushings to maintain precise suspension height. Sold in pairs. Note: the hard plastic bushings necessary for precision suspension movement may resonate noise on the street. General Fitment911 1987-89
$494.99
Make a selection JWST914PVT Durable, adjustable replacement for the rear trunk pivot. Bolt-in replacement does not require welding to install. Back-up plate reinforces the mounting area. The original pivot mount must be drilled or ground away and four new holes drilled for installation. Strong, smooth pivot will not bind or gall as can occur with the original design can be used with original torsion bars or aftermarket gas shocks. General Fitment914 1970-76
$59.50
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection RA2396X5RA2396X5 These axles are a direct bolt-in, featuring 108mm inner and outer cv's with exclusive aerospace grade internal cage and race set, with a bolt-on outer stub to fit the factory wheel hub. The center bars are high-grade aircraft quality torsional center bars that twist more than a factory unit absorbing a great deal of the shock factor and are made with 36 splines, upgraded from the factory 28 spline size. Rated to 1000hp with a 1-year warranty. Price listed is for both axles. General Fitment911 TURBO/GT2 2001-05
$3,401.97
Make a selection FVD116940 Anderungen der performance-kupplungsscheibe gegenuber der serien-kupplungsscheibe: der torsionsdampfer hat ein hoheres anschlagmoment: maximale belastbarkeit der torsionsdampfereinheit vor blockanschlag hoheres ubertragbares drehmoment anfahrverhalten ahnlich wie in serie bei fehlen der belagfeder ist das anfahrverhaltensportlicher, torsionsgefederte kupplungsscheiben dienen als schwingungsdampfer zwischen motor und getriebe.
$525.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |